no network

[lavlesh jain]

Can any one tell me the parmanent solution of no network found in 3100
Thaks in advance

[rashid]

dear br
its tested . resold filter and its linked components

[richard_wifi]

Can any one tell me the parmanent solution of no network found in 3100
Thaks in advance

bro...
1:bypass ur antenna sw then manual search...if ok replace antenna sw..
2:reheat/replace ur mjolner/rf ic then manual search...
3:flash with good pm file...

[stan1comm]

CHANGE THE UEM IT,S WORK

WWW.**************

[ajmal]

Can any one tell me the parmanent solution of no network found in 3100
Thaks in advance

due to falling down on floor or any other hard surface,signal disappear.
put some packing tape on the particular ic showed in attached image.
or give enough heat to reball that ic.
in most cases set got dead but no need to get worry .
remove that ic and put it back.I make many sets with this technique.
remove again and again ic and put it back untill ur set get start.
some conditions u have to flash it with latest flash files.
ic will not get damage to put it back again and again.
I also have one more solution for u.
but u have to wait for few hours.
I m working on another set.
after that i will send u image and written solution
try it and post results

[richard_wifi]

due to falling down on floor or any other hard surface,signal disappear.
put some packing tape on the particular ic showed in attached image.
or give enough heat to reball that ic.
in most cases set got dead but no need to get worry .
remove that ic and put it back.I make many sets with this technique.
remove again and again ic and put it back untill ur set get start.
some conditions u have to flash it with latest flash files.
ic will not get damage to put it back again and again.
I also have one more solution for u.
but u have to wait for few hours.
I m working on another set.
after that i will send u image and written solution
try it and post results

bro..thats the flash ic....the prob now is no network not cannot on or unknown flash...if u reball/reheat flash it will leave no effect on network...

[ajmal]

u never use this technique bro.
and I m using it from many weeks and use on many units.
dont niglect any method untill u personally and practically use it

[richard_wifi]

u never use this technique bro.
and I m using it from many weeks and use on many units.
dont niglect any method untill u personally and practically use it

bro..i think u need to go through the block that i posted...the flash ic does not function as RF controller but UPP does...so bro u need check on schematic diagram again and repost....

bro...let lavlesh jain repair his set and reply post.....

[ajmal]

bro I m not strictly recmmended that its the only last and final step to solve signal problem.
If problem in pa or rf or any other component.in that case u cant solve through flash ic.
its only in that case when ur set is damage due to drop fallen.

[ajmal]

here r few more images to solve signal problem in 3100

[danish jalal]

Can any one tell me the parmanent solution of no network found in 3100
Thaks in advance

bro check this pic ........
try and repaly.

[thushdt]

I have same problem with Nokia 1100. I reheat the PowerAmp & AntSw but no result. Can you help me too ?

[lavlesh jain]

thank u all of brothers for helping me I heat ant sw, filters,RF ic & at last by heating UEM my problem is solved. thanks & wish all members of gsmmind
a very HAPPY NEW YEAR 2008.

[ajmal]

congratulation bro..................

[joni_yang]

I have same problem with Nokia 1100. I reheat the PowerAmp & AntSw but no result. Can you help me too ?

bro,try to repalaced uem

good luck