Results 1 to 12 of 12

Thread: Samsung s3 i9300 & Note2 N7100 Dead boot repair solution & imei null solution only fo

  1. #1
    GsmIndia.in Pro jamesjerss's Avatar
    Join Date
    Apr 2010
    Location
    nagercoil,saudi
    Posts
    1,862

    Cool Samsung s3 i9300 & Note2 N7100 Dead boot repair solution & imei null solution only fo

    Samsung s3 i9300 & Note2 N7100 Dead boot repair solution & imei null solution only for i9300

    Procedure:

    * Download samsung s3 boot card maker Here

    * Extract it on desktop

    * Take a card reader insert memory card into the card reader nd connect it to the pc

    * From the extracted folder run Diskdump2.exe

    * Select generic storage Device. pictures below follw it



    * Now to write the scripts folle the below given picr




    Now done yu are succesfully created Dead boot memorycard

    To continue further

    Requerments:

    * Z3X samsung Box or SPT Box (i used z3x)

    * special UART Cable (300k or 500k uartcable)

    * Download teraterm-4.78 From
    Here

    * Fully charged battery

    Dead boot Reapairing procedure

    * Download nd extract teraterm-4.78 on desktop

    * From extracted folder run ttermpro.exe there select serial port nd change the serial port to z3x serial
    port lik below givin in the picr




    *After Select The Serial Port Press Ok Button den Go To Setup Click Serial Port Option
    Select Baud Rate 115200 Then Press Ok Button lik below givn in the picr






    * Now insert the created boot card to the mobile

    * Connect the Uart cable via z3x box

    * Now Insert the battery nd wait for 5min if the procces didnt start discnnt the mobile close ttermpro agin try it.

    * if it run success yu vil the result below given lik this.


    pit_check_integrity: invalid pit.(0x0)
    pit_check_integrity: invalid pit.(0x0)
    update_guid_partition_table: There is no pit binary.
    fsd_reclaim 1283: MST is not recognized(mst.magic=0x0)
    fsd_reclaim 1284: MST is not recognized
    fsd_reclaim 1599: Error(nErr=0x0)
    fsd_reclaim 1604: j4fs_rw_start is set to default value(128KB)
    j4fs_open 153: Error(nErr=0x40000000)
    j4fs_read_file_bootloader 355: j4fs panic
    load_j4fs_param: 'param.j4fs' does not exist, make new one..
    j4fs_write_file_bootloader 184: j4fs panic
    fail
    j4fs_read_file_bootloader 355: j4fs panic
    load_j4fs_param: debug level file does not exist..*INCORRECT!*
    init_fuel_gauge: battery is not detected, do not init fuelgauge
    init_microusb_ic: MUIC: CONTROL1:0x1b
    init_microusb_ic: MUIC: CONTROL1:0x1b
    init_microusb_ic: MUIC: CONTROL2:0x3b
    init_microusb_ic: MUIC: CONTROL2:0x3a
    PMIC_ID = 0x2
    PMIC_IRQSRC = 0x0
    PMIC_STATUS1 = 0x10
    PMIC_STATUS2 = 0x0
    PMIC_PWRON = 0x2
    PMIC_IRQ1 = 0x27
    PMIC_IRQ2 = 0x0
    s5p_check_keypad: keypad value=0x0
    s5p_check_reboot_mode: INFORM3 = 0 ... skip
    s5p_check_upload: MAGIC CODE=d1b0f038
    microusb_get_attached_device: STATUS1:0x3c, 2:0x0
    s5p_check_download: update mode=0
    j4fs_read_file_bootloader 355: j4fs panic
    s5p_check_tzsw: invalid tzsw type! dummy?
    scr_draw_image: draw 'download_error.jpg'...
    j4fs_read_file_bootloader 355: j4fs panic
    read_param_file: 'download_error.jpg' j4fs read failed!
    fimd_div:13, div:1, FB_SOURCE_CLOCK:800000000, FB_PIXEL_CLOCK:57153600
    a2, 60, 90,


    * if yu get this error at the end [Patch Stop] This is not Rom Code. yu cant fix yur mobile yu have to change yur emmc chip

    TN default
    <OK>
    <OK>
    [DVFS] INT(1) : 0
    DRAM Type : LPDDR2 8G
    [DVFS] MIF(3) : 0
    [EPLL][VPLL][CLK_DIV] OK
    <OK>
    [LOCK SW/HW]ARM:0/0 INT:0/0 G3D:0/0 MIF:0/0 SHIFT:0/0
    [DVFS] ARM(0) : 5
    [DVFS] INT(1) : 0
    [DVFS] G3D(2) : 0
    [DVFS] MIF(3) : 0
    [SD_INIT
    SDMMC_HighSpeedONE]
    SD_READ: 20000 20000 0x40008000 -> 668484 usec
    <OK>
    Inp32(uAddr) : 0xea00007e
    FW Booting
    [Patch Stop] This is not Rom Code.
    Last edited by jamesjerss; 12-10-2014 at 10:40 PM.

  2. #2
    GsmIndia.in Pro jamesjerss's Avatar
    Join Date
    Apr 2010
    Location
    nagercoil,saudi
    Posts
    1,862

    Default

    * After done this yur mobile must me n download mode or white screen if white screen manually put into download mode.

    * After dead boot repair mine white screen i manually put into download mode pir below



    * Now update your mobile with factory firmware with PIT file lik below given n the picr.Factory firmware Download Here



    * After update complete yur mobile may not have imei .imei null or yur mobile will not boot bcoz of dead boot repair. yur efs must be corrupted

    * To Fix this prob first root yur mobile
    Download from here (flash it through odin select as odin)

    * Now Download this EfS repair file nd flash it through odin select as odin yur mobile must boot
    but the imei become lik this 004999010640000

    I9300_Repair_efs.tar.rar



    * if yur imei is null yu cant repair using this box so 1st yu have to repair the efs using above givn file. if yur imei bcome lik tis oly (004999010640000) yu can repair using z3x or othr samsung tool

    * Now follw the picr to repair imei problem.






    * After IMEI Repair

    Last edited by jamesjerss; 14-02-2014 at 02:53 PM.

  3. #3
    GsmIndia.in Board Browser
    Join Date
    Mar 2014
    Age
    27
    Posts
    1

    Default

    my note 2 stuck at samsung boot logo
    Last edited by jamesjerss; 15-03-2014 at 06:07 PM.

  4. #4
    GsmIndia.in Pro jamesjerss's Avatar
    Join Date
    Apr 2010
    Location
    nagercoil,saudi
    Posts
    1,862

    Default

    Quote Originally Posted by abhi321 View Post
    my note 2 stuck at samsung boot logo
    try to hard rest it flash vit official last version firmware. while hard rest if yu se efs cant mount den repair efs usng octopus box den yur mob must boot aftr tat write imei follw the above procedure

  5. #5
    GsmIndia.in Active Teen born1972's Avatar
    Join Date
    Dec 2011
    Posts
    103

    Default

    Sir, I couldn't download Samsung s3 boot card maker. It just stuck in the middle of downloading. So, will you please re-post it again.

    Thanks in advance

  6. #6
    GsmIndia.in Active Teen born1972's Avatar
    Join Date
    Dec 2011
    Posts
    103

    Default

    Dear Sir Jamesjerss,

    I'm surprised to see it not downloading even after attempting for several times. I don't know if it's the problem of the internet connection or uploaded site. Is there other way around to download ?

    TIA

  7. #7
    GsmIndia.in Pro jamesjerss's Avatar
    Join Date
    Apr 2010
    Location
    nagercoil,saudi
    Posts
    1,862

    Default

    Quote Originally Posted by born1972 View Post
    Dear Sir Jamesjerss,

    I'm surprised to see it not downloading even after attempting for several times. I don't know if it's the problem of the internet connection or uploaded site. Is there other way around to download ?

    TIA
    Check now uploaded to mediafire link

  8. #8
    GsmIndia.in Active Teen born1972's Avatar
    Join Date
    Dec 2011
    Posts
    103

    Default

    Dear Sir Jamesjerss,

    I just want to know if the normal uart cable of s3 can repair the dead phone (samsung s3). I'm bit confused if the mentioned uart cable is the same that comes in the box package..

    Please let me know.

    TIA

    P.S. from where can i download samsung cable pin finder?
    Last edited by jamesjerss; 07-11-2014 at 03:26 AM.

  9. #9
    GsmIndia.in Pro jamesjerss's Avatar
    Join Date
    Apr 2010
    Location
    nagercoil,saudi
    Posts
    1,862

    Default

    Quote Originally Posted by born1972 View Post
    Dear Sir Jamesjerss,

    I just want to know if the normal uart cable of s3 can repair the dead phone (samsung s3). I'm bit confused if the mentioned uart cable is the same that comes in the box package..

    Please let me know.

    TIA

    P.S. from where can i download samsung cable pin finder?
    Yes yu can use normal uart cable cme vit the box

  10. #10
    GsmIndia.in Active Teen born1972's Avatar
    Join Date
    Dec 2011
    Posts
    103

    Default

    but sir which cable can i use 'cause the box doesn't include i9300. Is there any other uart cable that can be used coming along the box?

    TIA

  11. #11
    GsmIndia.in Active Teen born1972's Avatar
    Join Date
    Dec 2011
    Posts
    103

    Default

    Sir, is the cable c3300k or s7070 ? I tried with both but no response at all even after several attempts. Please let me know because it's very urgent.

    Thanks in advance

    Yu can also use usb jig no need to cnnt to the box vit uart cable if no response den must be hardware issue change emmc
    Last edited by jamesjerss; 09-11-2014 at 03:52 AM.

  12. #12
    GsmIndia.in Junior rockfort93's Avatar
    Join Date
    Nov 2012
    Age
    32
    Posts
    45

    Default

    Bro pls update the links it not working

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Samsung i9300 Imei Null/Unknown Baseband Repair Done Odin Vs Z3x
    By Service Team in forum Z3X-Team Products
    Replies: 33
    Last Post: 24-01-2015, 07:33 PM
  2. N7100 Note 2 / i9300 S3 " Easy " Boot Repair switch .
    By Service Team in forum Samsung Hardware Repair Section
    Replies: 3
    Last Post: 02-10-2014, 06:09 AM
  3. N7100 Note2 imei Null & Basband repair solution Here Tested
    By jamesjerss in forum Samsung Android Based Phones
    Replies: 20
    Last Post: 13-03-2014, 07:28 PM
  4. N7100 IMEI Repair Done III- Uart Cable Not Found Solution -III
    By Pak_mobile in forum Z3X-Team Products
    Replies: 2
    Last Post: 06-12-2013, 07:52 PM
  5. Replies: 0
    Last Post: 23-10-2013, 09:56 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •