Samsung Galaxy Y S5360 Android 2.3.6 India S5360DDLA1 Firmware Upgrade

[manoranjan2050]

Firmware info:
PDA: S5360DDLA1
PHONE: S5360DDLA1
CSC: S5360DDLA1
KERNEL: 2.6.35.7 dpi@DELL170#1
Version: Android 2.3.6 Gingerbread
Build: January 2012

DOWNLOAD

Password: samfirmware.com

Installation Tools

Odin 1.85

PIT File

~~Like My Post Just Click Like/Thanks Button~~

[manoranjan2050]

Here's the procedure on how to manually install the stock ROM (firmware) on Samsung Galaxy Y GT-S5360. Flashing stock ROMs is useful in downgrading or upgrading to any available firmware versions you desired. This has been also useful for unbricking purposes for a bricked, reverting back to original stock or if you needed your device warranty back.

This guide is a bit risky for beginners and can only be used by advance users who already had an experience on how to tweak android devices firmware.
Now, this procedure is no joke and should be taken seriously for it might results to damage your phone if some mistakes might happen. We are talking about firmware flashing here, one false move or any interruption will take your device into serious situation that is not too easy to recover.Your phone is not a toy for us, but it is your personal property, you are the only one who can decide on what to do about it.

Needed files and tools

Stock ROM

Odin 1.85

PIT file


Preparation before Flashing

Back-up all of your important data stored in the phone like contacts, messages and etc. Flashing will wipe and delete all of it.
Ensure that your phone is fully charge or above 80% charge.

Remove the SIM card and the external memory card. (not necessarily but recommended to avoid any certain issues)

Hard Reset - We often do hard reset before flashing to clean the memory cache of the phone. Master reset code *2767*3855# .

ODIN Flashing Procedures for Samsung S5360 Galaxy Y

1. Run the ODIN Downloader v1.84 on your PC desktop.

2. Load the firmware binary files on each designated button spaces.Click on each button and load the appropiate file unto it.
Pit Button - select and load the totoro_0623.pit


Bootloader - look for the file with the word Boot,
like DefaultCalDataWithBoot_S5360XXXXX_REV05.tar.md5


PDA button - look for the file with the letters PDA or CODE on it,
like PDA_S5360XXXXX_REV05.tar.md5


PHONE button- look with the word MODEM file,
like MODEM_S5360XXXXX_REV05.tar.md5


CSC button - associated also with letters CSC or Multi_CSC,
like GT-S5360-MULTI-CSC-OXXXXX.tar.md5

There are three checkboxes on the left side of ODIN, the Re-Partition, Auto Reboot and F.Reset Time.
The Auto Reboot and F.Reset Time are often always checked in flashing while the Re-Partition will only be checked if you want to fix the memory partition of the phone, now if you'll only want to upgrade or downgrade DO NOT CHECK THE REPARTITION.


DO NOT CHECK RE-PARTITION - Safety for Upgrade and Downgrade




Full Flashing with RE-PARTITION enabled - Advisable only for fixing Soft bricked devices



Setting up the Samsung Galaxy Y into Download Mode and Connecting to PC.
You need to set the device into download mode in order to let Odin recognize it. To set into download mode
Turn OFF the phone, then hold and press the three buttons Volume Down + Home + Power Key simultaneously. If you'll still not get into download mode, remove the battery a couple of seconds then put it back again and then press the download mode button combination again.

1y0o5v.jpg

Once the phone displays the Android robot and says "Downloading..." Connect the phone to PC with the supplied USB cable. Odin will automatically recognize it if it's properly connected, the ID:COM mapping will highlight to color yellow and says "added" on the log box.

Start Flashing
Hit the "Start" Button when all are set perfectly to begin flashing.

CAUTION: Avoid touching the phone while the flashing already started, any interruption will result into serious issues like soft-brick or hard-brick.

Let the flashing completes, a progress bar displays until the firmware downloading process finishes. It only takes around 3 to 5 minutes, depends of your PC speed.
When a word "PASS" appears, it means that the flashing is successful. The phone will then reboot and after completely rebooted it is then safe to remove it from computer's connection.




Do a hard reset again by the code *2767*3855# or in recovery mode hold and press Volume UP+Home+Power key. Navigate to the Wipe Data cache/Factory Reset.
Some other tweaks:
To check your recent firmware info *#1234#

If Any Problem Please Reply Post .

~~Like My Post Just Click Like/Thanks Button~~

[tsheikh95]

i like this software very much and your post was fabulous

[michaelcjohn]

thanx mate nice work

[vijaikumar86]

it's awsome my brother very importent post it;s brillient

[gcfhkv]

nice.............................................. .................................................. ...................

[sakiswd]

nice job tnx very match

[goldhofer]

u saved my day . . .Thanks alot

[Darklord1911]

thanks buddy............................................. .................

[Hydromj]

Thanks that helped alot

[raku087]

thanks a lot
its working........

[himms]

thanks for this great share

[krunal14320]

thanks for this great share

dsvzvzc thnxx a lott for this theread

[nitinarya]

thnxx dude ........ for the firmware

[nitinarya]

friend i cud nt find the PIT file .... will it raise a problem during or after flashing ..... please rply soon m waitinnn