1100 contact service

[sundar]

in 1100 i did one thing in pcb just reheat the uem for the no charging complaint after tat i switched on the phone it shows contact service i flashed in new version fully but still have the same problem any one help me........................................

[krishna]

its not software try reballing the UEM

[MUNEEB_AKHTAR_RAZA]

Yes mostly in this phone this cuased by hardware....SO try to check hardware properly!
Br
Muneeb Akhtar Raza

[AKKELECEN]

no hared
soft
mt.box

[.::Haji Bros::.]

in 1100 i did one thing in pcb just reheat the uem for the no charging complaint after tat i switched on the phone it shows contact service i flashed in new version fully but still have the same problem any one help me........................................

Hi Kanagavel, dear see with micro mirror that uem balls are safe from reheat if they are ok then erase flash and write new version of flash after that write pm file then do UISetting after following this procedure tell me what it says in result.
I recomend this Pm file it's uploaded here.
Best Regards

[$unil1989]

hi
i have reheat uem and i have flash
with v.mcu rh18_08.110 ppm rh18_08.11mb
this and wr pm 1100_pm.rar now also
this is same problum
tell me
thanks

[bond95]

hi
i have reheat uem and i have flash
with v.mcu rh18_08.110 ppm rh18_08.11mb
this and wr pm 1100_pm.rar now also
this is same problum
tell me
thanks

UEM not reheat just need reball .
After tray this

Start your UFS
Put manually your model
Take OFF point AUTODECT PROGUCT
Do full ERASE
Write Last version software MCU+PPM
Write Good short PM
Do UI SETTING but put just point INIT SIMLOCKS
Check your phone ...

[lucky]

hi
i have reheat uem and i have flash
with v.mcu rh18_08.110 ppm rh18_08.11mb
this and wr pm 1100_pm.rar now also
this is same problum
tell me
thanks

try to change uem & flash, if u dont find any result, forgot this set & give ur time to other phones

[dpimani]

Hi Kanagavel, dear see with micro mirror that uem balls are safe from reheat if they are ok then erase flash and write new version of flash after that write pm file then do UISetting after following this procedure tell me what it says in result.
I recomend this Pm file it's uploaded here.
Best Regards

1100 network is power on to few min gooan plz help me

[shorbagy]

thank you soooooooooooooo much

[lucky]

1100 network is power on to few min gooan plz help me

Write Good short PM
Do UI SETTING but put just point INIT SIMLOCKS
Check your phone ...if problm check track of PA. supply or change PA

[lucky]

1100 network is power on to few min gooan plz help me

Write Good short PM
Do UI SETTING but put just point INIT SIMLOCKS
Check your phone ...if problm, check track of PA.supply or change PA

[wissammo]

in 1100 i did one thing in pcb just reheat the uem for the no charging complaint after tat i switched on the phone it shows contact service i flashed in new version fully but still have the same problem any one help me........................................

recommend wissam
I think you must check imi on uem if ok do erase flash {mcu & ppm} then simloc then pm .
change {crystal 32MHZ}

[gautam4u]

in 1100 i did one thing in pcb just reheat the uem for the no charging complaint after tat i switched on the phone it shows contact service i flashed in new version fully but still have the same problem any one help me........................................

in 1100 i did one thing in pcb just reheat the uem for the no charging complaint after tat i switched on the phone it shows contact service i flashed in new version fully but still have the same problem any one help me

[saqib_islam]

try these solutions 100% Solved Here
1100 Contact Service Problem

If you like the post please HIT THANKS BUTTON