...::RIFF JTAG Updates Post Only Here::...
RIFF JTAG Updates Post Only Here
RIFF JTAG - CDMA HTC Droid Eris, HTC Polaris and more
12.04.2011 CDMA HTC Droid Eris, Unbrick, Boot Repair, ModelID repair supported
Resurrecting HTC Droid Eris is easy. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PB0010000′.
To resurrect HTC Droid Eris:
- Solder JTAG cable to HTC Droid Eris JTAG pads;
- Insert USB Data cable into board and PC;
- Make sure HTC Droid Eris is selected in the list of models;
- If you use battery, press Power On key;
- Click Resurrect button;
- Wait till software signals a successful operation completion;
- Disconnect power supply, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
To enter download mode:
- Disconnect PC cable;
- Insert battery;
- Hold ‘Volume down’ key and press ‘Power ON’ button to enter HBoot menu;
- Hold ‘Volume up’ key and press ‘Power ON’ button to enter Recovery mode;
12.04.2011 HTC Polaris (HTC Cruise) Unbrick, Unlock, IMEI and CID Update, ModelID repair supported
Resurrecting HTC Polaris is easy.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 2.20.AxeBox. Additionally, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘POLA10000′.
To resurrect HTC Polaris:
- Solder JTAG cable to HTC Polaris JTAG pads;
- Insert USB Data cable into board and PC;
- Make sure HTC Polaris selected in the list of models;
- If you use battery, press Power On key;
- Click Resurrect button;
- Wait till software signals a successful operation completion;
- Disconnect power supply, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing method
Whats new:
Added support for NOR Chips which have Intel/Sharp Extended Command Set (according to the CFI specification)
This means any NOR flash chip which is manufactured by CFI standard (it means all NOR flash chips) will be supported with above listed DLL-s. There is no need to update DCC Loaders for single flash chip ID, since configuration data are obtained from CFI.
RIFF JTAG - CDMA Samsung SCH-S109 (MSM6000) Repair supported and more !
20.04.2011 CDMA Samsung SCH-S109 (MSM6000) Repair supported
Resurrecting Samsung S109 is simple. Phone is auto powered on with charger connected; battery presence is not required.
Resurrector re-flashes only firmware zone of the phone (0×000000 to 0x3FFFFF).
To resurrect Samsung S109:
* Solder JTAG cable to Samsung S109 JTAG pads;
* Connect ignition cable for auto power on or use battery;
* Make sure Samsung S109 is selected in the list of models;
* Click Resurrect button;
* Wait till software signals a successful operation completion;
* De-solder JTAG wires;
20.04.2011 JTAG Manager v1.31, RIFF Box Firmware v1.23 released
Whats new :
JTAG Manager 1.31
* “RUN/STOP” Loaders functionality is added (and alternative to the DCC Loaders)
This is required for some ARM7 cores when Debug Communication Channel (DCC) to/from core is not functional (like in MSM6000)
Firmware 1.23
* Added 8/16/32-bit bus read/write access rotuines for ARM7 core
* ARM7 debug is now available in ARM/Thumb modes (use the GDBServer for this);
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
RIFF Box – JTAG Revolution
RIFF JTAG - CDMA Haier C3010, LG LSP450T Repair supported
22.04.2011 CDMA Haier C3010, LG LSP450T Repair supported
Resurrecting Haier C3010 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chips with IDs 0x00EC/0x257E and 0x017E/0×2210. Proper data will be selected automatically depending on memory ID in your device.
To resurrect Haier C3010:
- Solder JTAG cable to Haier C3010 JTAG pads;
- Insert USB Data cable into board and PC;
- Make sure Haier C3010 is selected in the list of models;
- Click Resurrect button;
- Choose which areas to flash;
- Wait till software signals a successful operation completion;
- De-solder JTAG wires;
Resurrecting LG LSP450T is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0×0020/0×8867
To resurrect LG LSP450T:
- Solder JTAG cable to LG LSP450T JTAG pads;
- Insert USB Data cable into board and PC;
- Make sure LG LSP450T is selected in the list of models;
- Click Resurrect button;
- Choose which areas to flash;
- Wait till software signals a successful operation completion;
- De-solder JTAG wires;
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
RIFF Box – JTAG Revolution
RIFF JTAG - More CDMA Today ! HTC Trophy Unlock, Unbrick and repair
Updates for today :
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
RIFF Box – JTAG Revolution
RIFF JTAG - CDMA Samsung S239 (MPower) Repair supported
26.04.2011 CDMA Samsung S239 (MPower) Repair supported
Resurrecting Samsung S239 is simple. Phone is auto powered on with USB Cable connected; battery presence is not required.
- To resurrect Samsung S239:
- Solder JTAG cable to Samsung S239 JTAG pads;
- Connect ignition cable for auto power on or use battery;
- Make sure Samsung S239 is selected in the list of models;
- Click Resurrect button;
- Wait till software signals a successful operation completion;
- De-solder JTAG wires;
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
RIFF Box – JTAG Revolution
RIFF JTAG - Samsung B2710 (Samsung Xcover 271) Unbrick / Repair supported
03.05.2011 Samsung B2710 (Samsung Xcover 271) Unbrick / Repair supported
Samsung B2710 resurrection is simple. Phone is auto powered on when USB Cable and battery are connected.
To resurrect Samsung B2710 do this:
- Solder JTAG cable to the Samsung B2710 JTAG pads;
- Connect USB cable to phone and PC;
- Make sure Samsung B2710 is selected in the list of models
- Click Resurrect button;
- Wait few seconds until software signals a successful operation completion;
- Disconnect USB cable, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.
To enter download mode:
- Disconnect PC cable;
- Insert battery;
- Hold both ‘Volume Down’ and ’9′ keys and press Power-On. Screen lights up with Download mode message.
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
RIFF Box – JTAG Revolution
RIFF JTAG - LG CU720 Shine Unbrick/Boot repair supported
07.05.2011 LG CU720 Shine Unbrick – Boot repair supported
Resurrecting LG CU720 is very hard because it requires non-beginner soldering skills (since JTAG pads on board are very small and are close to each other).
Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
To resurrect LG CU720:
- Solder JTAG cable to LG CU720 JTAG pads;
- Insert USB Data cable into board and PC;
- Make sure LG CU720 is selected in the list of models;
- Click Resurrect button;
- Wait till software signals a successful operation completion;
- Disconnect power supply, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
RIFF Box – JTAG Revolution
RIFF JTAG - More CDMA Models, Samsung S5250 Unbrick supported
New CDMA models added today :
- ZTE S160
- Unicare UN510BF
- Unicare ChivaC2
- Huawei C5100
- Samsung phones :
- Samsung S5250
- Samsung S5260 (Bug Fix)
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
RIFF Box – JTAG Revolution
RIFF JTAG – HTC Desire HD A9191 (HTC Ace) Unbrick, IMEI, CID, ModelID, Simlock repair
WHATS NEW!!!
- HTC Desire HD A9191 (HTC Ace) = Unbrick, IMEI, CID, ModelID, Simlock repair = WORLD FIRST ! ! !
Firmware 1.25
---------------------------
- added 5.0V USB Power On/Off controlling feature
- changed sequence for 32-bit write accesses for ARM11 core (MSM8xxx support)
JTAG Manager 1.33
---------------------------
- Improved connection policy:
Resurrection/DCC connection to device is implemented in such way that JTAG speed changes have 2 stages - booting stage and working stage.
Booting stage is the one from the connection start and until the DCC Loader upload is complete. Booting TCK/RTCK speed are setup
by JTAG Manager no matter what are the TCK settings by user (JTAG TCK Speed field in the JTAG Manager). Booting speed is hardcoded in the DLL.
After "booting" stage is complete, the "working" speed is set - the one which is selected by user in the JTAG TCK Speed field.
If Booting Speed in resurrector DLL is hardcoded as 'RTCK' the JTAG Manager would always use RTCK mode during booting stage.
Now policy is changed that is when user selects a fixed TCK frequency the JTAG Manager will automatically
change booting speed to the fixed TCK too.
- fixed bug: if "Use End Address" and "AutoFull Flash Size" were checked there was error setting valid length to read.
- for Advanced Users: advanced settings are now moved from the DCC Read/Write page ("Notifications...") into separate button on Box Service page (Advanced Settings button)
- added 5.0V USB Power On/Off controlling feature
For this go to Box Service page, click Advanced Settings: the Notifications dialog will be displayed,
go to "Advanced Settings" page and set desired mode for "Enable 5.0V output" checkbox.
When enabled, 5.0V power will be on after any "JTAG" operation executed and will remain "ON" until
box restart or until "Enable 5.0V output" checkbox is unchecked and any "JTAG" operation is executed.
- added optimization for flashing memory devices which are sector-based (like MDOC H3 or MMC/SD memory cards)
- if error code 0x3C (write-protect) is received no recover attempts are made.
RIFF Box – JTAG Revolution
RIFF JTAG - Samsung T749, Samsung E189 Unbrick - Boot repair supported
12.07.2011 Samsung T749, Samsung E189 Unbrick – Boot repair supported
he Samsung T749 board is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
To resurrect Samsung T749:
- Solder JTAG cable to Samsung T749 JTAG pads;
- Connect USB cable;
- Make sure Samsung T749 is selected in the list of models;
- Click Resurrect button;
- Wait till software signals a successful operation completion;
- Disconnect power supply, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
In case you cannot find firmware files use Global RIFF Link & Data Exchange plugin – at the moment of resurrector release there was shared full dump from alive Samsung T749 phone.
To enter download mode:
- Disconnect PC cable;
- Insert battery;
- Hold both ‘Volume Up’ and ‘Camera’ keys and press ‘Power ON’ button.
Resurrecting Samsung E189 is simple.
Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x00EC/0×2256
- To resurrect Samsung E189:
- Solder JTAG cable to Samsung E189 JTAG pads;
- Insert USB Data cable into board and PC;
- Make sure Samsung E189 is selected in the list of models;
- Click Resurrect button;
- Choose which areas to flash;
- Wait till software signals a successful operation completion;
- De-solder JTAG wires;
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.