Page 1 of 8 123 ... LastLast
Results 1 to 15 of 114

Thread: ...::RIFF JTAG Updates Post Only Here::...

  1. #1
    GsmIndia.in Team Legend shaiksha85's Avatar
    Join Date
    Sep 2009
    Location
    ...:: Bellary (karnatak) INDIA ::...
    Age
    39
    Posts
    8,743

    Default ...::RIFF JTAG Updates Post Only Here::...

    RIFF JTAG Updates Post Only Here


    RIFF JTAG - CDMA HTC Droid Eris, HTC Polaris and more

    12.04.2011 CDMA HTC Droid Eris, Unbrick, Boot Repair, ModelID repair supported

    Resurrecting HTC Droid Eris is easy. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
    Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PB0010000′.
    To resurrect HTC Droid Eris:

    • Solder JTAG cable to HTC Droid Eris JTAG pads;
    • Insert USB Data cable into board and PC;
    • Make sure HTC Droid Eris is selected in the list of models;
    • If you use battery, press Power On key;
    • Click Resurrect button;
    • Wait till software signals a successful operation completion;
    • Disconnect power supply, de-solder JTAG wires;

    Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.


    To enter download mode:

    • Disconnect PC cable;
    • Insert battery;
    • Hold ‘Volume down’ key and press ‘Power ON’ button to enter HBoot menu;
    • Hold ‘Volume up’ key and press ‘Power ON’ button to enter Recovery mode;


    12.04.2011 HTC Polaris (HTC Cruise) Unbrick, Unlock, IMEI and CID Update, ModelID repair supported

    Resurrecting HTC Polaris is easy.
    Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 2.20.AxeBox. Additionally, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘POLA10000′.

    To resurrect HTC Polaris:

    • Solder JTAG cable to HTC Polaris JTAG pads;
    • Insert USB Data cable into board and PC;
    • Make sure HTC Polaris selected in the list of models;
    • If you use battery, press Power On key;
    • Click Resurrect button;
    • Wait till software signals a successful operation completion;
    • Disconnect power supply, de-solder JTAG wires;

    Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing method

    Whats new:

    Added support for NOR Chips which have Intel/Sharp Extended Command Set (according to the CFI specification)

    This means any NOR flash chip which is manufactured by CFI standard (it means all NOR flash chips) will be supported with above listed DLL-s. There is no need to update DCC Loaders for single flash chip ID, since configuration data are obtained from CFI.

  2. #2
    GsmIndia.in Team Legend shaiksha85's Avatar
    Join Date
    Sep 2009
    Location
    ...:: Bellary (karnatak) INDIA ::...
    Age
    39
    Posts
    8,743

    Default RIFF JTAG - CDMA Samsung SCH-S109 (MSM6000) Repair supported and more !

    20.04.2011 CDMA Samsung SCH-S109 (MSM6000) Repair supported


    Resurrecting Samsung S109 is simple. Phone is auto powered on with charger connected; battery presence is not required.
    Resurrector re-flashes only firmware zone of the phone (0×000000 to 0x3FFFFF).



    To resurrect Samsung S109:

    * Solder JTAG cable to Samsung S109 JTAG pads;
    * Connect ignition cable for auto power on or use battery;
    * Make sure Samsung S109 is selected in the list of models;
    * Click Resurrect button;
    * Wait till software signals a successful operation completion;
    * De-solder JTAG wires;


    20.04.2011 JTAG Manager v1.31, RIFF Box Firmware v1.23 released


    Whats new :


    JTAG Manager 1.31

    * “RUN/STOP” Loaders functionality is added (and alternative to the DCC Loaders)

    This is required for some ARM7 cores when Debug Communication Channel (DCC) to/from core is not functional (like in MSM6000)


    Firmware 1.23

    * Added 8/16/32-bit bus read/write access rotuines for ARM7 core
    * ARM7 debug is now available in ARM/Thumb modes (use the GDBServer for this);


    Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

    RIFF Box – JTAG Revolution

  3. #3
    GsmIndia.in Team Legend shaiksha85's Avatar
    Join Date
    Sep 2009
    Location
    ...:: Bellary (karnatak) INDIA ::...
    Age
    39
    Posts
    8,743

    Default

    21.04.2011 CDMA Motorola W150i (MSM6000) Repair supported


    Resurrecting Motorola W150i is simple. Phone is auto powered on with charger connected; battery presence is not required. Pin TMODE has to be connected to GND in order to enable JTAG connection.
    Please note, MSM6000 draws power from JTAG pins, thus board can be detected via JTAG even without any power supplied. But for successful resurrection the power (battery or charger) is required. Thus when resurrection is complete don’t forget to disconnect phone from RIFF BOX to de-power it completely.



    • To resurrect Motorola W150i:
    • Solder JTAG cable to Motorola W150i JTAG pads;
    • Connect charger for auto power on or use battery;
    • Make sure Motorola W150i is selected in the list of models;
    • Click Resurrect button;
    • Choose which areas to flash;
    • Wait till software signals a successful operation completion;
    • De-solder JTAG wires;

    Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.



    RIFF Box – JTAG Revolution

  4. #4
    GsmIndia.in Team Legend shaiksha85's Avatar
    Join Date
    Sep 2009
    Location
    ...:: Bellary (karnatak) INDIA ::...
    Age
    39
    Posts
    8,743

    Default

    21.04.2011 CDMA Haier C300 Repair supported


    Resurrecting Haier C300 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.


    • To resurrect Haier C300:
    • Solder JTAG cable to Haier C300 JTAG pads;
    • Insert USB Data cable into board and PC;
    • Make sure Haier C300 is selected in the list of models;
    • Click Resurrect button;
    • Choose which areas to flash;
    • Wait till software signals a successful operation completion;
    • De-solder JTAG wires;


    21.04.2011 JTAG Manager 1.32 released
    ---------------------------
    Resurrector DLLs can now request current Memory Chip IDs
    This is most usefull for NOR-based devices since sometimes such devices require different firmware for different NOR memory chip IDs. Thus resurrector DLLs will be able to perform automatic selection of resurrection data.


    Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

  5. #5
    GsmIndia.in Team Legend shaiksha85's Avatar
    Join Date
    Sep 2009
    Location
    ...:: Bellary (karnatak) INDIA ::...
    Age
    39
    Posts
    8,743

    Default RIFF JTAG - CDMA Haier C3010, LG LSP450T Repair supported

    22.04.2011 CDMA Haier C3010, LG LSP450T Repair supported


    Resurrecting Haier C3010 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
    Current resurrector contains Firmware and EEPROM zones for memory chips with IDs 0x00EC/0x257E and 0x017E/0×2210. Proper data will be selected automatically depending on memory ID in your device.


    To resurrect Haier C3010:
    • Solder JTAG cable to Haier C3010 JTAG pads;
    • Insert USB Data cable into board and PC;
    • Make sure Haier C3010 is selected in the list of models;
    • Click Resurrect button;
    • Choose which areas to flash;
    • Wait till software signals a successful operation completion;
    • De-solder JTAG wires;

    Resurrecting LG LSP450T is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
    Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0×0020/0×8867


    To resurrect LG LSP450T:
    • Solder JTAG cable to LG LSP450T JTAG pads;
    • Insert USB Data cable into board and PC;
    • Make sure LG LSP450T is selected in the list of models;
    • Click Resurrect button;
    • Choose which areas to flash;
    • Wait till software signals a successful operation completion;
    • De-solder JTAG wires;

    Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.



    RIFF Box – JTAG Revolution

  6. #6

  7. #7
    GsmIndia.in Team Legend shaiksha85's Avatar
    Join Date
    Sep 2009
    Location
    ...:: Bellary (karnatak) INDIA ::...
    Age
    39
    Posts
    8,743

    Default RIFF JTAG - CDMA Samsung S239 (MPower) Repair supported


    26.04.2011 CDMA Samsung S239 (MPower) Repair supported



    Resurrecting Samsung S239 is simple. Phone is auto powered on with USB Cable connected; battery presence is not required.


    • To resurrect Samsung S239:
    • Solder JTAG cable to Samsung S239 JTAG pads;
    • Connect ignition cable for auto power on or use battery;
    • Make sure Samsung S239 is selected in the list of models;
    • Click Resurrect button;
    • Wait till software signals a successful operation completion;
    • De-solder JTAG wires;


    Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.


    RIFF Box – JTAG Revolution

  8. #8
    GsmIndia.in Team Legend shaiksha85's Avatar
    Join Date
    Sep 2009
    Location
    ...:: Bellary (karnatak) INDIA ::...
    Age
    39
    Posts
    8,743

    Default RIFF JTAG - Samsung B2710 (Samsung Xcover 271) Unbrick / Repair supported

    03.05.2011 Samsung B2710 (Samsung Xcover 271) Unbrick / Repair supported


    Samsung B2710 resurrection is simple. Phone is auto powered on when USB Cable and battery are connected.
    To resurrect Samsung B2710 do this:

    • Solder JTAG cable to the Samsung B2710 JTAG pads;
    • Connect USB cable to phone and PC;
    • Make sure Samsung B2710 is selected in the list of models
    • Click Resurrect button;
    • Wait few seconds until software signals a successful operation completion;
    • Disconnect USB cable, de-solder JTAG wires;

    Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.
    To enter download mode:
    • Disconnect PC cable;
    • Insert battery;
    • Hold both ‘Volume Down’ and ’9′ keys and press Power-On. Screen lights up with Download mode message.

    Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

    RIFF Box – JTAG Revolution

  9. #9
    GsmIndia.in Team Legend shaiksha85's Avatar
    Join Date
    Sep 2009
    Location
    ...:: Bellary (karnatak) INDIA ::...
    Age
    39
    Posts
    8,743

    Default

    04.05.2011 HTC Droid Incredible ADR6300 (HTC Incredible C) Unbrick Dead Boot Repair supported


    Resurrecting HTC Incredible C is easy. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
    Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PB3120000′.


    To resurrect HTC Incredible C:
    • Solder JTAG cable to HTC Incredible C JTAG pads;
    • Insert USB Data cable into board and PC;
    • Make sure HTC Incredible C is selected in the list of models;
    • If you use battery, press Power On key;
    • Click Resurrect button;
    • Wait till software signals a successful operation completion;
    • Disconnect power supply, de-solder JTAG wires;

    Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.


    To enter download mode:
    • Disconnect PC cable;
    • Insert battery;
    • Hold ‘Volume down’ key and press ‘Power ON’ button to enter HBoot menu;
    • Hold ‘Volume up’ key and press ‘Power ON’ button to enter Recovery mode;



    04.05.2011 Samsung Nexus S (i9023) Unbrick Boot repair supported

    Samsung I9023 is based on the S5PCxxx Processor (ARM core is Cortex-A8).
    Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on. But note, in very rare cases it is possible that you will have to hold Power On key during initial connection.
    Current resurrector has two different versions of primary boot loaders (PBL) embedded. This depends on hardware version of your phone which boot to use, thus in case of failure (cannot enter download mode after resurrection) of first loader try selecting another.
    In case after resurrection (after you have tried with both boot versions) the download mode is not initiated (LCD remains blank) do repeat resurrection with ‘Clone Gremlin zone’ option checked.



    To resurrect Samsung I9023:
    • Solder JTAG cable to Samsung I9023 JTAG pads;
    • Connect microUSB cable to phone and PC;
    • Insert battery;
    • Make sure Samsung I9023 is selected in the list of models;
    • Make sure a fixed TCK frequency is selected;
    • Click Resurrect button;
    • Wait till software signals a successful operation completion;
    • Disconnect USB cable, de-solder JTAG wires;

    Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

    To enter download mode:
    • Disconnect PC cable;
    • Insert battery;
    • Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.

    Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.


    RIFF Box – JTAG Revolution

  10. #10
    GsmIndia.in Team Legend shaiksha85's Avatar
    Join Date
    Sep 2009
    Location
    ...:: Bellary (karnatak) INDIA ::...
    Age
    39
    Posts
    8,743

    Default RIFF JTAG - LG CU720 Shine Unbrick/Boot repair supported

    07.05.2011 LG CU720 Shine Unbrick – Boot repair supported



    Resurrecting LG CU720 is very hard because it requires non-beginner soldering skills (since JTAG pads on board are very small and are close to each other).
    Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.


    To resurrect LG CU720:
    • Solder JTAG cable to LG CU720 JTAG pads;
    • Insert USB Data cable into board and PC;
    • Make sure LG CU720 is selected in the list of models;
    • Click Resurrect button;
    • Wait till software signals a successful operation completion;
    • Disconnect power supply, de-solder JTAG wires;

    Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.


    Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.



    RIFF Box – JTAG Revolution

  11. #11
    GsmIndia.in Team Legend shaiksha85's Avatar
    Join Date
    Sep 2009
    Location
    ...:: Bellary (karnatak) INDIA ::...
    Age
    39
    Posts
    8,743

    Default

    09.05.2011 RIFF JTAG – CDMA Day Again ! More power for Indian users !



    Whats new:
    Added Huawei CDMA models support :
    Huawei C2823 Repair, Read/Write NOR flash
    Huawei C2809 Repair, Read/Write NOR flash
    Huawei C2808 Repair, Read/Write NOR flash
    Huawei C2807 Repair, Read/Write NOR flash
    Huawei C2607 Repair, Read/Write NOR flash
    Huawei C2905 Repair, Read/Write NOR flash

    Added ZTE CDMA Model :
    ZTE C335 Repair, Read/Write NOR flash
    Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.


    http://www.jtagbox.com/

  12. #12
    GsmIndia.in Team Legend shaiksha85's Avatar
    Join Date
    Sep 2009
    Location
    ...:: Bellary (karnatak) INDIA ::...
    Age
    39
    Posts
    8,743

    Default RIFF JTAG - More CDMA Models, Samsung S5250 Unbrick supported

    New CDMA models added today :

    • ZTE S160
    • Unicare UN510BF
    • Unicare ChivaC2
    • Huawei C5100
    • Samsung phones :
    • Samsung S5250
    • Samsung S5260 (Bug Fix)


    Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.


    RIFF Box – JTAG Revolution

  13. #13
    GsmIndia.in Team Legend shaiksha85's Avatar
    Join Date
    Sep 2009
    Location
    ...:: Bellary (karnatak) INDIA ::...
    Age
    39
    Posts
    8,743

    Default RIFF JTAG – HTC Desire HD A9191 (HTC Ace) Unbrick, IMEI, CID, ModelID, Simlock repair

    WHATS NEW!!!


    - HTC Desire HD A9191 (HTC Ace) = Unbrick, IMEI, CID, ModelID, Simlock repair = WORLD FIRST ! ! !

    Firmware 1.25
    ---------------------------
    - added 5.0V USB Power On/Off controlling feature
    - changed sequence for 32-bit write accesses for ARM11 core (MSM8xxx support)



    JTAG Manager 1.33
    ---------------------------
    - Improved connection policy:
    Resurrection/DCC connection to device is implemented in such way that JTAG speed changes have 2 stages - booting stage and working stage.
    Booting stage is the one from the connection start and until the DCC Loader upload is complete. Booting TCK/RTCK speed are setup
    by JTAG Manager no matter what are the TCK settings by user (JTAG TCK Speed field in the JTAG Manager). Booting speed is hardcoded in the DLL.
    After "booting" stage is complete, the "working" speed is set - the one which is selected by user in the JTAG TCK Speed field.
    If Booting Speed in resurrector DLL is hardcoded as 'RTCK' the JTAG Manager would always use RTCK mode during booting stage.
    Now policy is changed that is when user selects a fixed TCK frequency the JTAG Manager will automatically
    change booting speed to the fixed TCK too.

    - fixed bug: if "Use End Address" and "AutoFull Flash Size" were checked there was error setting valid length to read.

    - for Advanced Users: advanced settings are now moved from the DCC Read/Write page ("Notifications...") into separate button on Box Service page (Advanced Settings button)

    - added 5.0V USB Power On/Off controlling feature
    For this go to Box Service page, click Advanced Settings: the Notifications dialog will be displayed,

    go to "Advanced Settings" page and set desired mode for "Enable 5.0V output" checkbox.
    When enabled, 5.0V power will be on after any "JTAG" operation executed and will remain "ON" until
    box restart or until "Enable 5.0V output" checkbox is unchecked and any "JTAG" operation is executed.


    - added optimization for flashing memory devices which are sector-based (like MDOC H3 or MMC/SD memory cards)

    - if error code 0x3C (write-protect) is received no recover attempts are made.



    RIFF Box – JTAG Revolution

  14. #14
    GsmIndia.in Active Teen mobile_zone1's Avatar
    Join Date
    May 2011
    Posts
    102

    Default

    RIFF JTAG - HTC Wildfire S A510E (HTC Marvel), 7 More CDMA models supported

    07.07.2011 HTC Wildfire S A510E (HTC Marvel), More CDMA models supported.


    Resurrecting HTC WildFireS is easy. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
    In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
    Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.01.0002 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PC4910000′. Additionally, you can check ‘Repair RECOVERY zones’ to reflash android BOOT and RECOVERY code.
    To resurrect HTC WildFireS:
    Solder JTAG cable to HTC WildFireS JTAG pads;
    Insert USB Data cable into board and PC;
    Make sure HTC WildFireS is selected in the list of models;
    If you use battery, press Power On key;
    Click Resurrect button;
    Wait till software signals a successful operation completion;
    Disconnect power supply, de-solder JTAG wires;
    Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
    To enter download mode:
    Disconnect PC cable;
    Insert battery;
    Hold ‘Volume Down’ key and press ‘Power ON’ button. In few seconds you should see usual android boot mode screen.



    Following CDMA models are supported from today :



    Samsung B139 Repair/Unbrick, Read/Write NOR Flash
    Samsung B259 Repair/Unbrick, Read/Write NOR Flash
    Samsung B309 Repair/Unbrick, Read/Write NOR Flash
    Samsung B319 Repair/Unbrick, Read/Write NOR Flash
    Samsung B379 Repair/Unbrick, Read/Write NOR Flash
    Samsung B619 Repair/Unbrick, Read/Write NOR Flash
    Huawei C31 Repair, Read/Write NOR flash


    Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.


    RIFF Box – JTAG Revolution

    http://www.jtagbox.com/

  15. #15
    GsmIndia.in Team Legend shaiksha85's Avatar
    Join Date
    Sep 2009
    Location
    ...:: Bellary (karnatak) INDIA ::...
    Age
    39
    Posts
    8,743

    Default RIFF JTAG - Samsung T749, Samsung E189 Unbrick - Boot repair supported

    12.07.2011 Samsung T749, Samsung E189 Unbrick – Boot repair supported


    he Samsung T749 board is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.

    To resurrect Samsung T749:

    • Solder JTAG cable to Samsung T749 JTAG pads;
    • Connect USB cable;
    • Make sure Samsung T749 is selected in the list of models;
    • Click Resurrect button;
    • Wait till software signals a successful operation completion;
    • Disconnect power supply, de-solder JTAG wires;

    Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
    In case you cannot find firmware files use Global RIFF Link & Data Exchange plugin – at the moment of resurrector release there was shared full dump from alive Samsung T749 phone.

    To enter download mode:
    • Disconnect PC cable;
    • Insert battery;
    • Hold both ‘Volume Up’ and ‘Camera’ keys and press ‘Power ON’ button.




    Resurrecting Samsung E189 is simple.


    Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
    Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x00EC/0×2256


    • To resurrect Samsung E189:
    • Solder JTAG cable to Samsung E189 JTAG pads;
    • Insert USB Data cable into board and PC;
    • Make sure Samsung E189 is selected in the list of models;
    • Click Resurrect button;
    • Choose which areas to flash;
    • Wait till software signals a successful operation completion;
    • De-solder JTAG wires;




    Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

Page 1 of 8 123 ... LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Replies: 0
    Last Post: 12-05-2011, 07:03 PM
  2. Replies: 0
    Last Post: 23-04-2011, 10:43 AM
  3. RIFF JTAG Updates - HTC Ozone/Chief, JTAG Manager v1.29 and more
    By shaiksha85 in forum Gsm Updates & News
    Replies: 0
    Last Post: 31-03-2011, 09:04 PM
  4. Replies: 0
    Last Post: 24-09-2010, 07:24 PM
  5. RIFF JTAG Updates - Samsung i780 pda repair added
    By maverick_lp28 in forum RIFF JTAG Box
    Replies: 2
    Last Post: 17-07-2010, 04:55 AM

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •