jaf repair tool one exe with video for beginners

[snipper_gsm]

jaf repair tool one exe with video

http://www.mediafire.com/?zji4km1qjwl

http://www.4shared.com/file/uKOT4zcA/JAF_TOOL.html

http://www.megafileupload.com/en/fil...-TOOL-rar.html

http://www.megafileupload.com/en/fil...-TOOL-rar.html

[91909]

There is a procedure to repair ATMega128 of JAF
Needed par port on computer. I post here details with process of programme if any user need it.

[snipper_gsm]

Thanks for comments sir.. this is procedure. picture. and exe package video guide..

To solve this we need this

TOOLS and STEPS:

1. MPROG - EEPROM DATA MEMORY PROGRAMMER

MProg 3.5

2. PONYPROG - ATMEGA MEMORY PROGRAMMER

PONY PROG 2000


Take a look for the function of this two Software:


FIRST PROBLEM = BOX DETECTED AS USB SERIAL

MPROG EASY STEPS

[snipper_gsm]

FLASHING

After THAT: RECONNECT THE BOX and it will be detected as JAF INTERFACE FLASHER.


SECOND PROBLEM = CAN'T DETECT PHONE ON FBUS CHK

NOW we will use PONYPROG but this time we will use COM PORT.
BAKIT? Karamihan ng PC MOTHER BOARD ngayun walang SERIAL-PRINTER PORT

[snipper_gsm]

TOOLS AND SETTINGS:

FEMALE COM PORT


HERE IS THE COMPLETE SETUP

No resistors added, direct to the PC and ATMEGA.

Before that cut this first.

[snipper_gsm]

Open ponyprog and set to com not parallel

Open file select erase HEX FILE then flash, Open again select ATMEGA BIN FILE then write to device.


NOTE: UNLOCK this box


RECONNECT the line you cut in PCB

[91909]

Brother I just Add a small thing.
You can programme Jaf ATMega128 using ponyprog also from LPT port and no need to cut or solder
I just past photograph of RIPGSM for illustration
(This tech. is devloped by my friend ripgsm from italy and his team)


1. Solder 2 nos of wire from ATMega128 of JAF as shown in picture



2. Cut a Rj45 cable and find out 4 and 5 as shown in the picture



Join 2 wire from 4 and 5 and connect rj45 with JAF

3. How to connect wires from PC LPT port.



Connect all 4 wires and jaf USB cable

Open ponyprog and start as mentioned above

No need to cut or past any thing Only need a RJ45 cable 4 nos wire and solder 2 points from JAF's ATMEGA128.

[91909]

The 4 and 5 are miso and mosi
No need to programme with MProg
I found many box wich are erased by it and after that They failed to recover

AVOID MProg
Mprog is used for eeprom program. If need download good ept and write it only after read. No do anything morethen that otherwise may cuse jaf usb to serial device or dual serial and you can't recover it.
Ponyprog is only solution for dead jaf or not botting.

[chanakacin]

Please Help.
I can write programe data with blank hex file but when i write bin file it fails.

[Service Team]

Please Help.
I can write programe data with blank hex file but when i write bin file it fails.

need log br.,

we want more information

can you post your log br.,

[chanakacin]

need log br.,

we want more information

can you post your log br.,

I searched few post and i found that my ATMEGA128 chip is damaged. I couldn't find ATMEGA128 so i replaced with ATMEGA128A. Datasheet says it's same. when i repair it as this guide it worked fine. but now i'm facing another issue. I can do INF but i cannot do CHK. I checked my cables and the rj45 connector. all of those are fine.

Switching to serial...
Powering the phone...
Reading...
MCU SW version: V ICPR72_10w29_tube1
24-05-11
RM-356
(c) Nokia
HW version: 1101
PCI version:
RFIC version:
DSP version:
Retu version: 16
Tahvo version: 22
Production serial number: CZB681854
Product code: 0577187
Module code: 0204538
Basic production code: 0552692
Flash code:
Order number:
Product specific data:
Long production SN: 0
ATO:
Default SN type:
IMEI plain: 353382042216429
IMEI spare to net: 3A 35 83 02 24 12 46 02
IMEI SV to net: 33 35 83 02 24 12 46 72 F4

LOCK STATUS:

CONFIG KEY: 8000000000000000
PROVIDER KEY: 4500000088401881
Provider: Unknown provider
Key Code count: 3, FBUS Code count: 0

Block 1:
Lock 1: CLOSED -> Lock Data: 450FFF

Searching for saved ini...
Checking for file C:\Program Files\ODEON\JAF\JAF_RM-356.ini
Saved INI not found, loading INI list...
Setting local mode...
Reading product code...
Product Code: 0577187
Searching for JAF saved location of ini...
Checking path: C:\Program Files\Nokia\Phoenix\Products\RM-356\

Searching for default location of ini...
Checking path: \Products\RM-356\
Searching for JAF saved location of ini...
Checking path: C:\Program Files\Nokia\Phoenix\Products\RM-356\
No ini files found...
FILES SET FOR FLASHING:
MCU Flash file: NONE
PPM Flash file: NONE
CNT Flash file: NONE
APE Variant file: NONE
Done!
Booting phone...
FAST PHONE detected!

CMT Boot Data:
Asic ID: 000000010000022600010006400C192101051103
Asic Mode ID: 00
Asic EM ID: 00000B22
Asic Public ID: 0140010C5C990052B786FE77EA066AE2FAC364C7
HASH: 479C6DDE3942E12C429C1D6ADED8037100000000
ROM ID: 4B9B75103E691FF8
Error finding cmt boot file...

In DCT4
Getting MCU ID

MCU ID: 0xFF07
Can't find boot file...
Failed! Aborting!
Done!
Phone Restarted...