myphone s21 unlock succes.

[marvino13]

again myphone s21 unlock succes unlock flash po procedure mabilis pa

COM7 [VCP0] selected
module v2.83
Device: MyPhone-S21
Checking data, wait...
advanced flash detection enabled
Action: write NOR flash
"smart write" active
write: Firmware
MyPhone-S21_TINNO23_07A_PCB01_GPRS_MT6223_S00.T01_23_07A_W 0736_MP_FMCAM-FTP_V0_08_En.B0M.bin
skip: Customization/Language Pack
skip: Customization
skip: Eeprom/ffs
Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6223:8A04:8A00]...
CPU: MT6223
chip: 0011:4D30:000C
status: FF
boot packet size: 0400
Release Power button now !
Boot Done
Initialize ...
detecting chip #00 in region #00...
flash: 01227E22202200:2AEA0000000000
flash: Amd AMD/Fujitsu std [D 0004x010000 003Ex040000 0004x010000] 16Mb
number of flash chip/regions detected: 01/01
Initialize Done
Set baud ...
921600
Set baud Done
Initialize bootcode ...
Initialize bootcode Done
Check firmware integrity ...
detect device identification#1...
detection phase #1...
detect device identification#1 finished
identification#1 structure: 2nd [enhanced] generation
security area (code #1) is Ok
security area (code #1) backup saved: C:\Program Files\InfinityBox\MModule\backup_security\id.4EE80 C9F.[TINNO23_07A_PCB01_GPRS_MT6223_S00.T01_23_07A_W0736 _MP_FMCAM-FTP_V0_08.BIN_61396B89].rpl
identification#1 detection finished
device-id: 4EE80C9F
identification#1 protocol ver: 04
ver. sw 1: TINNO23_07A_PCB01_GPRS_MT6223_S00.T01_23_07A_W0736 _MP_FMCAM-FTP_V0_08.BIN
ver. sw 2: T01_23.07A.W0736.MP.FMCAM-FTP_V0.08, 7694C69E
ffs offset/size: 00800000/00800000
ffs address assigned: 00800000
detect device identification#2...
detection phase #1...
.
detect device identification#2 finished
sim-lock status: unknown
Check firmware integrity Done
Check firmware content ...
Check firmware content Done
Backup required data ...
Backup required data Done
Patch required data ...
Patch required data Done
Special operation ...
firmware patch sp-lock #0/0 applied
firmware patch sp-lock #1 is not required
firmware patch sp-lock #2 is not required
Special operation Done
Write ...
detect device identification#2...
detection phase #1...
.
detect device identification#2 finished
security area (code #1) check...
security area (code #1) calculation...
security area (code #1) fixed
file saved: C:\Program Files\InfinityBox\MModule\backup_security\MyPhone-S21_TINNO23_07A_PCB01_GPRS_MT6223_S00.T01_23_07A_W 0736_MP_FMCAM-FTP_V0_08__system_log_4EE80C9F_61396B89_20090918-142522.B0X.bin
Area: Firmware
flash: 01227E22202200:2AEA0000000000
Write: Firmware
detect device identification#2...
detection phase #1...
.
detect device identification#2 finished
Write Done
Finalization ...
Finalization Done
file saved: C:\Program Files\InfinityBox\MModule\backup_security\MyPhone-S21_TINNO23_07A_PCB01_GPRS_MT6223_S00.T01_23_07A_W 0736_MP_FMCAM-FTP_V0_08__system_log_4EE80C9F_61396B89_20090918-142545.B0X.bin
Finished, time used: 43 sec
Remove/Install battery now !

[arabhella]

where did you downloaded the flashfile. . ., please upload a link. . ., thanks in advance

[Service Team]

where did you downloaded the flashfile. . ., please upload a link. . ., thanks in advance

this is old post

you need file kindly post new thread

1. what you needed ?

2. you need flash file kindly add screen- shot r log

then you request it

your file link : http://www.4shared.com/rar/Eov_-nAq/..._and_unlo.html