GT-i9300 stuck on samsung logo and there is no PIT partition

[obidulmomin]

I have samsung i9300 that stuck on samsung logo while booting.
I used Odin and I9300XWUGML4_I9300ODDGML4_TML fimware.
When I click on start, an error would come up There is no PIT partition

<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXUGNB4_I9300XSAGMK3_I9300XXUGNA8_HOME.tar.md 5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003>
<ID:0/003> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)

[shaiksha85]

Bro

Load Both Pit & Firmware And Try Again

If Still You Have Problem Try It In Flashing Box

[obidulmomin]

Thanks For Kind Reply.
I tried with Pit and Firmware.
I also tried different type of pit file for GT-i9300.
But No result.
I think Partition Table Demaged .
May be from hardware .
In your reply you suggested to use flasher box.
Which flasher box you recommend or is it recommended to use Jtag.
I have no jtag available now.

[shaiksha85]

Thanks For Kind Reply.
I tried with Pit and Firmware.
I also tried different type of pit file for GT-i9300.
But No result.
I think Partition Table Demaged .
May be from hardware .
In your reply you suggested to use flasher box.
Which flasher box you recommend or is it recommended to use Jtag.
I have no jtag available now.

Z3x Or Asansam

Try This Repair Firmware : I9300XXUGMK6_OXAGMK6_v4.3_Repair_Firmware

[obidulmomin]

Z3x Or Asansam

Try This Repair Firmware : I9300XXUGMK6_OXAGMK6_v4.3_Repair_Firmware

Bro,
Via Fbus or Usb?
I already tried with z3x samsung tool v24.3 via usb.
No success.

[starmobi]

Bro,
Via Fbus or Usb?
I already tried with z3x samsung tool v24.3 via usb.
No success.

post your z3x screenshot.....

[shaiksha85]

Bro,
Via Fbus or Usb?
I already tried with z3x samsung tool v24.3 via usb.
No success.

Yes Its USB Flash

If Still You Are Getting Error
Change USB If Not Sucess

Sure its HARDWARE

[obidulmomin]

post your z3x screenshot.....

Yes Its USB Flash

If Still You Are Getting Error
Change USB If Not Sucess

Sure its HARDWARE

I have tested Different PC and Different type of usb cable.
I also changed USB port.
I included screenshot below.
Please check in and Help.

Without Pit File



With Pit File

[One_Hermit]

Check Product Name in Download Mode [OK or Blank]

[obidulmomin]

Check Product Name in Download Mode [OK or Blank]

Thanks for your kind reply.
Product Name in Download Mode is Blank.

b-S3-2.jpg

[One_Hermit]

Use EasyJTAG or Other Supported Box to Repair
If Same Change EMMC