-RESTORATION FILES AND BY PASS PACKAGE PRESENT-



This steps should work with all DB2012 CID52 phones, but for this de******ion, iīve used a W200i phone.
To apply in another models, just use appropriate files (Drivers and Restore) for desired phone.

1 - Make sure that you are using latest SETool SW version (v0.914031 currently), and your phone must
have fully charged battery.

2 - Turn on your phone without SIM inserted. Attatch it to USB (DCU-60) cable and, when prompted,
install appropriate drivers (you can find all drivers that you need on "download/software files/
drivers for CSCA procedure/" folder on SETool support area).

3 - Start SETool SW. On "Settings" tab, check both "SIGNED MODE (USE SERVER FOR BYPASS/CSCA)" and
"ENABLE ALTERNATIVE SECURITY BYPASS" options.

4 - Now go to "Sony Ericsson" tab, select correct phone model and press "Identify".
Attach turned off phone to USB cable and hold "C" key. Check if the restoration file is present.
If yes, go to step 7. If not, continue reading. Check the provider that the phone is locked to
(in this example, phone is locked to vodafone uk provider), because you will need to use an
accepted SIM or a Test SIM during this process. Check the SW of the phone too (in this example,
R4JA011 Generic ME) to locate appropriate restore file. If you canīt found your needed restore file,
follow THIS thread to request it or use FLASH Method.

5 - To find your restore file, go to SETool support area ("download/software files/original setool2
rest files/collection" folder), search for it and download file to "Rest" folder inside SETool main folder.

6 - To be sure that youīve downloaded correct rest file, press "Identify" again and check info

7 - Now, press "Unlock/Repair" function and attach turned off phone to USB cable holding "C" key. unlock process
will start.

8 - When prompted, disconnect phone, insert an accepted SIM card (in this example, vodafone uk SIM) or Test SIM,
turn it on and continue holding "C" key during powering process.

9 - When phone is fully turned on, attach it to USB cable. Phone will be found by SETool SW and unlock process
will continues

10 - Normally phone will restart by itself. If itīs not, remove battery, insert on phone again and attach

phone to USB cable holding "C" key. SETool will continue to unlock phone.

11 - Now just wait until unlock procedure done. Usually entire process goes on 160~180 secs,

-RESTORATION FILES NOT PRESENT/ UNLOCK VIA FLASHING METHOD-



This unlock procedure must be used if you donīt have RESTORE file for your phoneīs SW version, and canīt get it,
or in any other untypical situation. This steps should work with all DB2012 CID52 phones, but for this de******ion,
iīve used a W200i phone. To apply in another models, just use appropriate files (Drivers and MAIN+FS) for desired phone.

1 - Make sure that you are using latest SETool SW version (v0.914031 currently), and your phone must have fully charged
battery.

2 - Turn on your phone without SIM inserted. Attach it to USB (DCU-60) cable and, when prompted, install appropriate
drivers (you can find all drivers that you need on "download/software files/drivers for CSCA procedure/" folder
on SETool support area).

3 - Start SETool SW. On "Settings" tab, check "SIGNED MODE (USE SERVER FOR BYPASS/CSCA)", "ENABLE ALTERNATIVE
SECURITY BYPASS", "COMPLETE PHONE AFTER FLASH" and "UNLOCK AFTER FLASH" options

4 - Now go to "Sony Ericsson" tab, select correct phone model and press "Identify". Attach turned off phone to
USB cable and hold "C" key. Verify SW version installed on phone, CID version and check the provider that the phone
is locked to , because your will need to use an accepted SIM or TEST SIM during this process.


5 - Go to SETool support area and download appropriate SW version for your phone. If you canīt locate exactly version,
use highest version possible. Double check CID file version. It must be CID 52. Now, press "Add" button and
add MAIN and FS files. You can also use "Custpacks" if you need.

6 - Press "Flash" button and attach turned off phone to USB cable, holding "C" key. Phone will be detected and flash
procedure will starts.

7 - When prompted, disconnect phone, insert an accepted SIM card (in this example, VODAFONE UK SIM) or Test SIM,
turn it on and continue holding "C" key during powering process

8 - When phone is fully turned on, attach it to USB cable. Phone will be found by SETool SW and unlock process
will continues.

9 - SETool SW will write MAIN and FS files to phone, than will start unlock procedure.

10 - In the end, if everything goes fine, you will receive "Phone detached, Elapsed Time" message. You phone
is now ready to work with any providerīs SIM card

br