i need flash file for gfive u505

[chaurasiy]

here is my log

Initializing...
DA_LIB_VER_3.9.0.0
It is sensing the pinout fast...
D-=10 D+=9
Searching commport...please wait...
Connecting...
Spd USB-to-Serial=COM9
Connected...sending boot...
FDL test...OK
ArmBootMode: 6610000000945A00_01
Wait for init Commzero Security Engine...
Done.
Loading bootloader...
Done.
Changing baudrate...
Set baudrate to 115200 is ok
Reading phone HW info...
Read info is done.
CPU: SC6610/20 Flash: SF_GD25Q32
setting the Flash Parameters...
Settings have been completed!
setting the Serial Flash Parameters...
Settings have been completed!
Reading FileSystem info...

[chaurasiy]

i need a flash file for kfive k 598+


here is log


Initializing...
DA_LIB_VER_3.9.0.0
It is sensing the pinout fast...
RXD=10 TXD=9
Connecting...
Connected...sending boot...
FDL test...OK
ArmBootMode: 6600700900026A00_01
Wait for init Commzero Security Engine...
Done.
Loading bootloader...
Done.
Changing baudrate...
Set baudrate to 115200 is ok
Reading phone HW info...
Read info is done.
CPU: SC6600L7 Flash: NOR_ST_M30L0T7000T0
setting the Flash Parameters...
Settings have been completed!
Reading FileSystem info...

[REALFRIENDS]

Please Serch Hear
http://www.gsmindia.in/forum/gpg-dra...ash-files.html

[chaurasiy]

thankx bro......but i did not get my files

i need urgent i need a flash file for kfive k 598+


here is log


Initializing...
DA_LIB_VER_3.9.0.0
It is sensing the pinout fast...
RXD=10 TXD=9
Connecting...
Connected...sending boot...
FDL test...OK
ArmBootMode: 6600700900026A00_01
Wait for init Commzero Security Engine...
Done.
Loading bootloader...
Done.
Changing baudrate...
Set baudrate to 115200 is ok
Reading phone HW info...
Read info is done.
CPU: SC6600L7 Flash: NOR_ST_M30L0T7000T0
setting the Flash Parameters...
Settings have been completed!
Reading FileSystem info..

[PALMOBILE@SAMSUNG]

dear master
here is your solution

http://www.4shared.com/file/pUnB23u1/J-STAR_U505_SPD.html

REGARDS
PALMOBILE
@SERVICE TEAM

[chaurasiy]

gfive L6100 dead after formatting


Initializing...
DA_LIB_VER_4.0.3.2
It is sensing the pinout fast,please hold on the phone Power key
RXD=7 TXD=9
Connecting...Please hold on the POWER key until the red gauge is going...
Any errors please select another boot and try again.
BB:6253, HardwareVer:8A00, SoftwareVer:8A02
Loading boot...
INT_SYSRAM_BOOT test completed.
Loading boot...
Boot2 test completed.
Nor Flash ID: 0098009E00000000
Nand Flash ID: 0000000000000000
Read Hardware Information is done.
Config EMI(Nor Flash only)...
Failed to check H/W.
Get Project ID from phone...
Project ID: GFIVE-MUL1_S331v01.03b01
Changing baudrate to 921600...
Done.
Formatting Flash...
AutoFormat address: start=0x00E00000, size=0x00200000
All Done




IT GIVES ERROR WITH BACKUP FILE

Initializing...
DA_LIB_VER_4.0.3.2
It is sensing the pinout fast,please hold on the phone Power key
RXD=7 TXD=9
Connecting...Please hold on the POWER key until the red gauge is going...
Any errors please select another boot and try again.
BB:6253, HardwareVer:8A00, SoftwareVer:8A02
Loading boot...
INT_SYSRAM_BOOT test completed.
Loading boot...
Boot2 test completed.
Nor Flash ID: 0098009E00000000
Nand Flash ID: 0000000000000000
Read Hardware Information is done.
Config EMI(Nor Flash only)...
Failed to check H/W.
Get Project ID from phone...
Project ID: GFIVE-MUL1_S331v01.03b01
Changing baudrate to 921600...
Done.
Analysis the file, Some file may need a long time...
The file has not been encrypted.
Downloading Flash file...
Failed to set MTK_DA_WRITE_CMD


WHAT CAN I DO ..........PLEASE HELP

[Service Team]

bro take back-up then flash it............

post ur reply.......

download

[shaiksha85]

thankx bro......but i did not get my files

i need urgent i need a flash file for kfive k 598+


here is log


Initializing...
DA_LIB_VER_3.9.0.0
It is sensing the pinout fast...
RXD=10 TXD=9
Connecting...
Connected...sending boot...
FDL test...OK
ArmBootMode: 6600700900026A00_01
Wait for init Commzero Security Engine...
Done.
Loading bootloader...
Done.
Changing baudrate...
Set baudrate to 115200 is ok
Reading phone HW info...
Read info is done.
CPU: SC6600L7 Flash: NOR_ST_M30L0T7000T0
setting the Flash Parameters...
Settings have been completed!
Reading FileSystem info..

Try This http://www.ziddu.com/download/187398...SPDOK.rar.html

[chaurasiy]

bro take back-up then flash it............

post ur reply.......

download

bro i take back up................but it gives errror

Initializing...
DA_LIB_VER_4.0.3.2
It is sensing the pinout fast,please hold on the phone Power key
RXD=7 TXD=9
Connecting...Please hold on the POWER key until the red gauge is going...
Any errors please select another boot and try again.
BB:6253, HardwareVer:8A00, SoftwareVer:8A02
Loading boot...
INT_SYSRAM_BOOT test completed.
Loading boot...
Boot2 test completed.
Nor Flash ID: 0098009E00000000
Nand Flash ID: 0000000000000000
Read Hardware Information is done.
Config EMI(Nor Flash only)...
Failed to check H/W.
Get Project ID from phone...
Project ID: GFIVE-MUL1_S331v01.03b01
Changing baudrate to 921600...
Done.
Analysis the file, Some file may need a long time...
The file has not been encrypted.
Downloading Flash file...
Failed to set MTK_DA_WRITE_CMD

[chaurasiy]

i need flash file for gfive l6100 here is log

Initializing...
DA_LIB_VER_4.0.3.2
It is sensing the pinout fast,please hold on the phone Power key
RXD=7 TXD=9
Connecting...Please hold on the POWER key until the red gauge is going...
Any errors please select another boot and try again.
BB:6253, HardwareVer:8A00, SoftwareVer:8A02
Loading boot...
INT_SYSRAM_BOOT test completed.
Loading boot...
Boot2 test completed.
Nor Flash ID: 0098009E00000000
Nand Flash ID: 0000000000000000
Read Hardware Information is done.
Config EMI(Nor Flash only)...
Failed to check H/W.
Get Project ID from phone...
Project ID: GFIVE-MUL1_S331v01.03b01
Changing baudrate to 921600...
Done.